Detailed Information |
Bus Analyzer Software
CompactPCI Generic Carrier Card (6U) for PMC (PCIbus Mezzanine Card) modules
- Easily configured with any AIM PMC Databus Module: AFDX/ARINC664, ARINC429, MIL-STD-1553 or any standard Third Party PMC module
- Mix and Match different Databus Modules with the ACC-2
- Rear I/O available for ACC-2
- 66Mhz operation for +3.3V environments
- +5.0V signaling environment available
- 64 bit PCI bus extension
- Fully compliant to CompactPCI Specification
- Hosts PMC interface designed to PMC standard P1386.1/Draft 2.4
Detailed Information |
Bus Analyzer Software
CompactPCI Generic Carrier Cards for PMC (PCIbus Mezzanine Card) modules
General Features
The ACP-1 is member of AIM’s new family of 64bit extended PMC Carrier Boards. The ACP-1 is a ‘Short Length PCI’ module format with one PMC slot to plug in a standard PMC module. The ACP-1 implements a PCI-to-PCI Bridge using the industry standard INTEL device. It fulfils the requirements of the PCI Bus Specification Revision 2.3, for both the Primary and Secondary side. The PMC-slot is in conformance with the Draft Standard Physical and Environmental Layers for PCI Mezzanine Cards (P1386.1/Draft 2.4).
PMC Module Interface
The ACP-1 is designed to plug all standard PMC modules with a maximum PCIbus width of 64bit and a PCIbus operation frequency up to 66 MHz.
The ACP-1 carrier board Interface is of an Universal I/O signalling voltage type and can be plugged in either a +3.3V or +5.0V PCI- Slot.
On the secondary PCIbus side, the PMC slot is configured to support +3.3V, I/O signalling voltage for use with +3.3V PMC modules. For +5.0V PMC modules the Carrier is identified by a different part number. The use of a voltage keying pin protects against false PMC assembly.
Key Features- Easily configured with any AIM PMC Databus Module: AFDX/ARINC664, ARINC429, MIL-STD-1553 or any standard Third Party PMC module.
- Up to 66MHz operation for +3.3V environments
- +5.0V signalling environment available
- 64 bit PCI bus extension
- Fully compliant to PCI Specification, Rev. 2.3
- Hosts PMC interface designed to PMC standard P1386.1/Draft 2.4
- Onboard Ribbon cable connector provided for access to the PMC- Rear I/O signals (P14)
- On-board -12VDC Power Supply (up to 10 Watts) to supply ARINC429 Transmitters
Detailed Information |
Bus Analyzer Software
AXI-PSI-16
General Features
The AXI-PSI-16 is a ‘C Sized’ VXIbus module, providing simulation, monitoring, protocol testing and data selection of 8 Transmit (Tx) and 8 Receive (Rx) Serial Data Channels according to the PANAVIA interface standard specification.
The advanced hardware architecture provides powerful resources (processing performance and memory size) to guarantee fully concurrent availability of all specified PANAVIA Interface functions simultaneously on all Tx and Rx channels.
The 8 Transmit (Tx) Channels on the AXI-PSI-16 module acts as an autonomously operating data communication simulator, supporting a continuous transmission sequence with user definable data words.
The 8 Receive (Rx) channels on the AXI-PSI-16 module provides the PANAVIA standard decoding with unique on-board error detection, triggering and data selection capability.
The AXI-PSI-16 module is a “register-based device” and can be easily integrated into VXI Systems as an off-the-shelf module supported by an VXI “plug&play” driver software package. The AXI-PSI-16 also operates with the optional ‘PANalyser’ Databus Analyser software package for WINDOWS.
PANAVIA Receiver
Key Features of the 8 Receiver Channels are:- Decoding 16Bit Data & Status Words
- Tag orientated Data Storage or
- Chronological Data Storage
- Tag Selective Data Filtering
- Comprehensive Error Detection of:
- Control Bit Error
- Framing Error
- Bit Count Error
- Sync Bit Error
- Parity Error
- Programmable Interrupts & Trigger on:
- Definable Tag Receipt
- Definable Data Word Receipt
- Erroneous Data Receipt
- Loss of Clock / Data
- IRIG- B Time Tagging on Received Data with a resolution of 1µsec
PANAVIA Transmitter
Key Features of the 8 Transmitter Channels are:- Encoding PANAVIA Protocol Format
- Continuous Data & Clock Transmission
- Programmable Tag Sequence
- Selective Transmission Frequency of 64KHz or 62,5KHz
- Programmable Interrupts on:
- Definable Tag Transmissions
- End of Transfer List
- Full Error Injection on each Tag Transfer: Bit Count, Parity, Framing, Sync Bit, Control Bit
Application Support Processor
The 150 MHz ASP Application Support Processor provides unique on-board processing functions typically provided by host processing systems.
Operational features include:- Driver Software Execution on-board
- Control of RS232C debug Port for Firmware Updates
- User Application processing on-board
IRIG-B Time Code Decoder
An on-board IRIG-B time code decoder and generator allow synchronisation of PANAVIA bus traffic. Multiple AXI-PSI-16 modules can be synchronised using one common IRIG-B time source or the on-board time code generator of one AXI-PSI-16 modules as the reference for accurate correlation of data across multiple PANAVIA data streams.
Physical Bus Interface
A Physical Bus Interface daughter board (PBI) provides PANAVIA connection to the data channels via a Mini D-Sub Connector.
Detailed Information |
Bus Analyzer Software
CompactPCI Generic Carrier Card (3U) for PMC (PCIbus Mezzanine Card) modules
- Easily configured with any AIM PMC Databus Module: AFDX/ARINC664, ARINC429, MIL-STD-1553 or any standard Third Party PMC module.
- Mix and Match different Databus Modules with the ACC-2
- Rear I/O available for ACC-2
- 66Mhz operation for +3.3V environments
- +5.0V signaling environment available
- 64 bit PCI bus extension
- Fully compliant to CompactPCI Specification
- Hosts PMC interface designed to PMC standard P1386.1/Draft 2.4
Detailed Information |
Bus Analyzer Software
CompactPCI Generic Carrier Cards for PMC (PCIbus Mezzanine Card) modules
General Features
The ACC-1 and ACC-2 are members of AIM’s new family of 64bit extended PMC Carrier Boards. The ACC-1 is a single slot, single height (3U) CompactPCI module with one PMC slot to plug in a standard PMC module, whilst the ACC-2 is a single slot, double height (6U) CompactPCI module to plug in two standard PMC modules. Both implement a PCI-to-PCI Bridge using the industry standard INTEL device.
The ACC-1 and ACC-2 fulfil the requirements of the CompactPCI specification as well as the requirements of the PCIbus standard both Primary and Secondary sides. The PMC-slot is in conformance with the Draft Standard Physical and Environmental Layers for PCI Mezzanine Cards (P1386.1/Draft 2.4).
PMC Module Interface
The ACC-1/ ACC-2 are designed to plug all standard PMC modules with a maximum PCIbus width of 64bit and a PCIbus operation up to 66 MHz.
The ACC-1/ ACC-2 carrier board is of Universal I/O signaling voltage type and can be plugged in either a +3.3V or +5.0V CPCI chassis. On the secondary PCIbus side the PMC slot is configured to support +3.3V, I/O signaling voltage for use with +3.3V PMC modules. For +5.0V PMC modules the Carrier is identified by a different part number. The use of a voltage keying pin protects against false PMC assembly.
Key Features- Easily configured with any AIM PMC Databus Module: AFDX/ARINC664, ARINC429, MIL-STD-1553 or any standard Third Party PMC module
- Mix and Match different Databus Modules with the ACC-2
- Rear I/O available for ACC-2
- 66Mhz operation for +3.3V environments
- +5.0V signaling environment available
- 64 bit PCI bus extension
- Fully compliant to CompactPCI Specification
- Hosts PMC interface designed to PMC standard P1386.1/Draft 2.4
Detailed Information |
Bus Analyzer Software
AXI-PSI-16
General Features
The AXI-PSI-16 is a ‘C Sized’ VXIbus module, providing simulation, monitoring, protocol testing and data selection of 8 Transmit (Tx) and 8 Receive (Rx) Serial Data Channels according to the PANAVIA interface standard specification.
The advanced hardware architecture provides powerful resources (processing performance and memory size) to guarantee fully concurrent availability of all specified PANAVIA Interface functions simultaneously on all Tx and Rx channels.
The 8 Transmit (Tx) Channels on the AXI-PSI-16 module acts as an autonomously operating data communication simulator, supporting a continuous transmission sequence with user definable data words.
The 8 Receive (Rx) channels on the AXI-PSI-16 module provides the PANAVIA standard decoding with unique on-board error detection, triggering and data selection capability.
The AXI-PSI-16 module is a “register-based device” and can be easily integrated into VXI Systems as an off-the-shelf module supported by an VXI “plug&play” driver software package. The AXI-PSI-16 also operates with the optional ‘PANalyser’ Databus Analyser software package for WINDOWS.
PANAVIA Receiver
Key Features of the 8 Receiver Channels are:- Decoding 16Bit Data & Status Words
- Tag orientated Data Storage or
- Chronological Data Storage
- Tag Selective Data Filtering
- Comprehensive Error Detection of:
- Control Bit Error
- Framing Error
- Bit Count Error
- Sync Bit Error
- Parity Error
- Programmable Interrupts & Trigger on:
- Definable Tag Receipt
- Definable Data Word Receipt
- Erroneous Data Receipt
- Loss of Clock / Data
- IRIG- B Time Tagging on Received Data with a resolution of 1µsec
PANAVIA Transmitter
Key Features of the 8 Transmitter Channels are:- Encoding PANAVIA Protocol Format
- Continuous Data & Clock Transmission
- Programmable Tag Sequence
- Selective Transmission Frequency of 64KHz or 62,5KHz
- Programmable Interrupts on:
- Definable Tag Transmissions
- End of Transfer List
- Full Error Injection on each Tag Transfer: Bit Count, Parity, Framing, Sync Bit, Control Bit
Application Support Processor
The 150 MHz ASP Application Support Processor provides unique on-board processing functions typically provided by host processing systems.
Operational features include:- Driver Software Execution on-board
- Control of RS232C debug Port for Firmware Updates
- User Application processing on-board
IRIG-B Time Code Decoder
An on-board IRIG-B time code decoder and generator allow synchronisation of PANAVIA bus traffic. Multiple AXI-PSI-16 modules can be synchronised using one common IRIG-B time source or the on-board time code generator of one AXI-PSI-16 modules as the reference for accurate correlation of data across multiple PANAVIA data streams.
Physical Bus Interface
A Physical Bus Interface daughter board (PBI) provides PANAVIA connection to the data channels via a Mini D-Sub Connector.
CompactPCI Generic Carrier Card (6U) for PMC (PCIbus Mezzanine Card) modules
- Easily configured with any AIM PMC Databus Module: AFDX/ARINC664, ARINC429, MIL-STD-1553 or any standard Third Party PMC module
- Mix and Match different Databus Modules with the ACC-2
- Rear I/O available for ACC-2
- 66Mhz operation for +3.3V environments
- +5.0V signaling environment available
- 64 bit PCI bus extension
- Fully compliant to CompactPCI Specification
- Hosts PMC interface designed to PMC standard P1386.1/Draft 2.4
CompactPCI Generic Carrier Cards for PMC (PCIbus Mezzanine Card) modules
General Features
The ACC-1 and ACC-2 are members of AIM’s new family of 64bit extended PMC Carrier Boards. The ACC-1 is a single slot, single height (3U) CompactPCI module with one PMC slot to plug in a standard PMC module, whilst the ACC-2 is a single slot, double height (6U) CompactPCI module to plug in two standard PMC modules. Both implement a PCI-to-PCI Bridge using the industry standard INTEL device.
The ACC-1 and ACC-2 fulfil the requirements of the CompactPCI specification as well as the requirements of the PCIbus standard both Primary and Secondary sides. The PMC-slot is in conformance with the Draft Standard Physical and Environmental Layers for PCI Mezzanine Cards (P1386.1/Draft 2.4).
PMC Module Interface
The ACC-1/ ACC-2 are designed to plug all standard PMC modules with a maximum PCIbus width of 64bit and a PCIbus operation up to 66 MHz.
The ACC-1/ ACC-2 carrier board is of Universal I/O signaling voltage type and can be plugged in either a +3.3V or +5.0V CPCI chassis. On the secondary PCIbus side the PMC slot is configured to support +3.3V, I/O signaling voltage for use with +3.3V PMC modules. For +5.0V PMC modules the Carrier is identified by a different part number. The use of a voltage keying pin protects against false PMC assembly.
Key Features- Easily configured with any AIM PMC Databus Module: AFDX/ARINC664, ARINC429, MIL-STD-1553 or any standard Third Party PMC module
- Mix and Match different Databus Modules with the ACC-2
- Rear I/O available for ACC-2
- 66Mhz operation for +3.3V environments
- +5.0V signaling environment available
- 64 bit PCI bus extension
- Fully compliant to CompactPCI Specification
- Hosts PMC interface designed to PMC standard P1386.1/Draft 2.4
|
AXI-PSI-16
General Features
The AXI-PSI-16 is a ‘C Sized’ VXIbus module, providing simulation, monitoring, protocol testing and data selection of 8 Transmit (Tx) and 8 Receive (Rx) Serial Data Channels according to the PANAVIA interface standard specification.
The advanced hardware architecture provides powerful resources (processing performance and memory size) to guarantee fully concurrent availability of all specified PANAVIA Interface functions simultaneously on all Tx and Rx channels.
The 8 Transmit (Tx) Channels on the AXI-PSI-16 module acts as an autonomously operating data communication simulator, supporting a continuous transmission sequence with user definable data words.
The 8 Receive (Rx) channels on the AXI-PSI-16 module provides the PANAVIA standard decoding with unique on-board error detection, triggering and data selection capability.
The AXI-PSI-16 module is a “register-based device” and can be easily integrated into VXI Systems as an off-the-shelf module supported by an VXI “plug&play” driver software package. The AXI-PSI-16 also operates with the optional ‘PANalyser’ Databus Analyser software package for WINDOWS.
PANAVIA Receiver
Key Features of the 8 Receiver Channels are:- Decoding 16Bit Data & Status Words
- Tag orientated Data Storage or
- Chronological Data Storage
- Tag Selective Data Filtering
- Comprehensive Error Detection of:
- Control Bit Error
- Framing Error
- Bit Count Error
- Sync Bit Error
- Parity Error
- Programmable Interrupts & Trigger on:
- Definable Tag Receipt
- Definable Data Word Receipt
- Erroneous Data Receipt
- Loss of Clock / Data
- IRIG- B Time Tagging on Received Data with a resolution of 1µsec
PANAVIA Transmitter
Key Features of the 8 Transmitter Channels are:- Encoding PANAVIA Protocol Format
- Continuous Data & Clock Transmission
- Programmable Tag Sequence
- Selective Transmission Frequency of 64KHz or 62,5KHz
- Programmable Interrupts on:
- Definable Tag Transmissions
- End of Transfer List
- Full Error Injection on each Tag Transfer: Bit Count, Parity, Framing, Sync Bit, Control Bit
Application Support Processor
The 150 MHz ASP Application Support Processor provides unique on-board processing functions typically provided by host processing systems.
Operational features include:- Driver Software Execution on-board
- Control of RS232C debug Port for Firmware Updates
- User Application processing on-board
IRIG-B Time Code Decoder
An on-board IRIG-B time code decoder and generator allow synchronisation of PANAVIA bus traffic. Multiple AXI-PSI-16 modules can be synchronised using one common IRIG-B time source or the on-board time code generator of one AXI-PSI-16 modules as the reference for accurate correlation of data across multiple PANAVIA data streams.
Physical Bus Interface
A Physical Bus Interface daughter board (PBI) provides PANAVIA connection to the data channels via a Mini D-Sub Connector.
|
|
VME Generic Carrier Card for PMC (PCIbus Mezzanine Card) modules
- Easily configured with any AIM PMC Databus Module: AFDX/ARINC664, ARINC429, MIL-STD-1553 or any standard Third Party PMC module
- Combine different interface types and functions on one VME card
- User configurable base address
- Front panel LED’s for VMEbus/PCIbus activity/failure display
- Fully compliant to VME64x – extended VMEbus
- Hosts PMC modules designed to PMC standard P1386.1/Draft 2.4
- Driver Software Library for VxWorks and LynxOS available
VME Generic Carrier Card for PMC (PCIbus Mezzanine Card) modules
General Features
The AVC-2 is a single slot, double height (6U) VME64x, extended VMEbus module with two separate PMC slots. The AVC-2 uses an on board, industry standard, Tundra chip (Universe II) providing the bridge between the VMEbus and PCIbus. The AVC-2 fulfils the requirements of the VME64x extension plus the Interface for Rear I/O. Each PMC-slot is in conformance with the Draft Standard Physical and Environmental Layers for PCI Mezzanine Cards (P1386.1/Draft 2.4).
Key features of the AVC-2 module:- Easily configured with any combination of PMC modules
- Combine different interface types and functions on one VME card
- User configurable base address
- Front panel LED’s for VMEbus/PCIbus activity/failure display
- Fully compliant to VME64x – extended VMEbus
- Hosts PMC modules designed to PMC standard P1386.1/Draft 2.4
- Driver Software Library for VxWorks and LynxOS available
PMC Module Interface
The AVC-2 is designed to plug all standard PMC modules with a maximum PCIbus width of 64bit operating at 33MHz.
The AVC-2 carrier board supports the +5.0V PCIbus signalling, hence only +5.0V tolerant devices may be used. The use of a voltage keying pin protects against false PMC assembly.
|
AXI-PSI-16
General Features
The AXI-PSI-16 is a ‘C Sized’ VXIbus module, providing simulation, monitoring, protocol testing and data selection of 8 Transmit (Tx) and 8 Receive (Rx) Serial Data Channels according to the PANAVIA interface standard specification.
The advanced hardware architecture provides powerful resources (processing performance and memory size) to guarantee fully concurrent availability of all specified PANAVIA Interface functions simultaneously on all Tx and Rx channels.
The 8 Transmit (Tx) Channels on the AXI-PSI-16 module acts as an autonomously operating data communication simulator, supporting a continuous transmission sequence with user definable data words.
The 8 Receive (Rx) channels on the AXI-PSI-16 module provides the PANAVIA standard decoding with unique on-board error detection, triggering and data selection capability.
The AXI-PSI-16 module is a “register-based device” and can be easily integrated into VXI Systems as an off-the-shelf module supported by an VXI “plug&play” driver software package. The AXI-PSI-16 also operates with the optional ‘PANalyser’ Databus Analyser software package for WINDOWS.
PANAVIA Receiver
Key Features of the 8 Receiver Channels are:- Decoding 16Bit Data & Status Words
- Tag orientated Data Storage or
- Chronological Data Storage
- Tag Selective Data Filtering
- Comprehensive Error Detection of:
- Control Bit Error
- Framing Error
- Bit Count Error
- Sync Bit Error
- Parity Error
- Programmable Interrupts & Trigger on:
- Definable Tag Receipt
- Definable Data Word Receipt
- Erroneous Data Receipt
- Loss of Clock / Data
- IRIG- B Time Tagging on Received Data with a resolution of 1µsec
PANAVIA Transmitter
Key Features of the 8 Transmitter Channels are:- Encoding PANAVIA Protocol Format
- Continuous Data & Clock Transmission
- Programmable Tag Sequence
- Selective Transmission Frequency of 64KHz or 62,5KHz
- Programmable Interrupts on:
- Definable Tag Transmissions
- End of Transfer List
- Full Error Injection on each Tag Transfer: Bit Count, Parity, Framing, Sync Bit, Control Bit
Application Support Processor
The 150 MHz ASP Application Support Processor provides unique on-board processing functions typically provided by host processing systems.
Operational features include:- Driver Software Execution on-board
- Control of RS232C debug Port for Firmware Updates
- User Application processing on-board
IRIG-B Time Code Decoder
An on-board IRIG-B time code decoder and generator allow synchronisation of PANAVIA bus traffic. Multiple AXI-PSI-16 modules can be synchronised using one common IRIG-B time source or the on-board time code generator of one AXI-PSI-16 modules as the reference for accurate correlation of data across multiple PANAVIA data streams.
Physical Bus Interface
A Physical Bus Interface daughter board (PBI) provides PANAVIA connection to the data channels via a Mini D-Sub Connector.
|
|
|
|
|
